• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

Reasons Your fiat key replacement 500 Key Fob Won't Work

A fiat key cover 500 key fob allows you to easily open doors and start your car. There are a myriad of reasons why the key fob might stop functioning. This could be due to a dead coin-battery, water damage, issues with the receiver module, and interference.

This listing is for an new fiat 500 key replacement fiat 500 key fob not working Flip Key Remote - like the Ilco brand that needs how to get a new fiat 500 key be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob being inoperative. Modern key fobs operate with a limited operating range, and should be within a few feet of the vehicle to operate. If you're far from your vehicle and hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens then replace the battery for your coin-cell (Part Number CR2032) with a new battery of a reliable brand, such as Panasonic Duracell or Energizer. You can find them in the local hardware store or on the internet.

You can test the battery on your coin-cell by pressing the buttons while standing near your fiat 500 key replacement 500. The parking lights should blink and the key fob will operate the lock and unlock switch.

If your key fob still does not work after replacing the battery, there may be water damage that has prevented it from interacting with the module inside your vehicle. Water damage can occur in a number of ways, ranging from small splashes to submerging the fob in salt water at the beach. If you suspect that your fob has been exposed to water, you can place it in a rice bag to draw out the moisture. If this doesn't work, you will need to have the fob reset by an auto locksmith or a dealer.

Water Damage

While the fob has some rubber seals to keep water from the electronic chip inside and out of the ocean or washing it in a machine could cause water damage. Saltwater poses a particular risk to the circuit board of the fob and can cause it to short out and eventually end up dying. It's not the best idea to let the fob get wet however, don't give it up if you accidentally drop it in the water or don't take it out of your pants pocket.

First take the battery off the fob. Before replacing the battery, clean the electronic chip using isopropyl or another similar product. Next check the fob to see if it works. If the key doesn't function, it may have to be changed. This is usually handled by a professional or dealer auto locksmith.

If your key is old and has not been programmed for your vehicle it is necessary to replace it completely. This is an easy process that can be handled by a professional automotive locksmith. The locksmith will require the key to be cut to match your vehicle's ignition. They'll also need to program the fob into your vehicle's system. This is a low-cost and quick process that could be completed the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob may stop functioning is because it's out of range. The remote usually has an operating range of 30 feet or less and if it's far from your vehicle, it won't respond to your commands. You can easily fix this by moving the remote closer to your car until it responds.

If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and your fob still won't work it could be due to an internal circuit board problem. Reprogramming the fob is usually the solution to this issue. You can find the instructions for the majority of vehicles on YouTube or in the owner's manual.

You may have to replace the metal clips that keep the coin battery. If they loose tension, it can prevent your coin battery from sitting properly and cause your remote to malfunction.

In rare cases the fob could be disconnected from your vehicle due to software issues or hardware issues. This could be a huge problem, but you can usually fix it by visiting a local dealer or auto locksmith to reprogram your fob for you. In some cases, they may need to reinstall the program in your body control module, as well.

Interference

Interference can also cause the key fob not to receive or transmit the signal. This is possible when the key fob is near a radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob may not function due to a bad connection to the buttons, water damage or damage to the internal chips.

If the key fob has stopped working one day out of the blue or even after trying everything you can do at home to fix it e.g. replacing batteries, reprogramming or using the spare key fob, you could have a faulty receiver module on your 500. The receiver module, which is located beneath the dashboard, detects radio frequency signals from your key fob. It transforms the signals into electronic commands which are then processed by the vehicle.

There is a straightforward method to reset the 500's onboard system including the keyfob. Disconnect the 12 volt battery for about 15 minutes, by removing the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electricity, and restart the car's computer. This can help get your key fob to work again. If the issue continues you should speak with a certified technician. They will be able to diagnose the exact cause of your problems.