• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

Reasons to Change Door Lock

There are many reasons to change the door lock, from improving your home's security to redecorating your entrance. It is also possible to change locks if the key gets stuck or is difficult to turn.

DIY novices can also alter their locks. Get the tools you need to begin.

Remove the old lock

Removing the lock that was previously installed from the door is a necessary step prior to installing the new one. This is essential if you suspect someone else has a key to the house. This is an excellent idea after you've moved into your new home, experienced a burglary or welcomed a roommate. It's much easier than you think and can be completed in a matter of minutes.

Start by removing the screws holding the deadbolt faceplate on the door frame. To remove the faceplate, you'll need to remove screws on both sides. This will allow you see what's behind it and provide you with the knowledge of how to continue with the rest of steps.

Once you have removed your old faceplate, then you have to remove the bolt and strike plate. Remove the bolt from the door hole using the screwdriver. If the bolt is rusted you may have to use a chisel to hammer it. When using a chisel to remove the bolt, make sure to not to scratch the door frame.

Make sure that the new doorknob, deadbolt and lock will fit in the holes that are already present in the door before you take out the old one. Many hardware stores and large box stores have a wide selection of locks and can assist you in choosing the right one. Ask for help if the lock you purchased isn't the right one for your door.

While you are removing the old lock, search for small depressions or notches in the handle or around the trim. If you find them, insert a straightened safety pin or flat screwdriver through them to release the handle and expose the screws beneath.

After you have removed the screw from the handle, you can begin removing the knob. To do this, find the set screw located at the base of the knob, and loosen it. Next, you will need to remove the knob from the spindle. Finally, carefully remove the spindle from the door.

Install the new lock

It is a good idea to change the locks on your doors periodically, especially if you have been the victim of a break-in. It's simple, inexpensive and effective to change the lock on your door. The majority of people can do it themselves with a screwdriver and some basic directions. Depending on the circumstances, you may also need to learn how to rekey a door lock to ensure that you only have the key.

You will need to purchase a new lock with the same keyway as your current lock. Most locksmiths will replace your lock at an additional cost, but you can save money by doing it yourself. You can purchase a new lock from an hardware store, or on the internet. A standard deadbolt should be able to fit on doors of all sizes however, you'll have to measure the size of your door to make sure that it fits.

The majority times your new lock will come with the cardboard template that will show how it will fit on the door. It can be used as a reference for drilling the hole, which is much more convenient than measuring every time. If the template doesn't match to your hole, you should return it to the hardware store and get an alternative.

When installing the new lock, you must be sure to place it on the right side of the door. You can verify this by inspecting the latch, which must be labelled "up" or something similar. Make sure that the latch is correctly seated on the plate and then attach it using the supplied screws.

If you are replacing a door knob lock, it's also important to pay attention to the way it's operated. Most knob locks are left-handed however, there are some that are right-handed. If you're not careful, the upvc window lock repairs near me could be placed on the wrong side of your door, which will hinder it from locking either from the inside or outside.

It is recommended to test the new lock after you finish. You should be able to lock and unlock the door using keys from the inside as well as the outside. If you're not happy with the result, you can get a locksmith to fix it.

Test the broken window lock repair

If a lock on your door won't unlock can be frustrating and can be dangerous, it could also put your family's security at risk. It's easy to fix the majority of problems with door locks by performing some troubleshooting, and lubrication. To start with, check that your key is correctly cut and that the lock itself isn't loose or dirty. If this doesn't resolve the problem, you can try lubricating the door lock actuator with powdered graphite or a silicone-based lubricant.

Then, make sure that the door lock switch, the wiring harnesses and the actuator connector are working correctly. Refer to the wiring diagram or manual to determine the color-coding and function of each wire of the door lock switch. Use a digital meter or test light to verify that the actuator is receiving power and ground whenever the switches are activated. If you notice an electric voltage switch on every switch activation, this means the switches are working and it's probably the actuator that needs to be replaced.

If the switch seems to work, but the actuator doesn't move when you turn the knob, it could be a problem with the actuator itself. The actuator cylinder has spring-loaded pins that stop the cylinder from moving until a key is inserted and it pushes the pins up to accommodate the key's height in that location. Then, the cylinder to rotate and open the lock body and allow the handle to latch.

If the door lock actuator is still inoperable, you can remove the switch and wires from the actuator with small screwdrivers to unlock the upvc window locking mechanism repair bolt and separate the plastic cover that houses the electrical connector. After that, disconnect the door lock actuator, and let it fall. Then you should be able to locate and remove the two bolts that are that hold the actuator in position. Once the actuator is removed, you will be in a position to disconnect the black electrical connector and then pull it out along with the actuator and lock assembly.

Replace the key

Whether you have an unkeyed deadbolt or door knob If it's not working properly you need to either change the lock's key or rekey it or replace it completely. It's not difficult to do this yourself and can save lots of money. But, prior to doing this it is a good idea to have a locksmith examine the locks and look for any issues. This will give you peace of mind that your home is safe and safe.

To begin, take off the faceplate on the outside from the deadbolt or doorknob. There may be screws that are holding it in place, then use a screwdriver loosen them and then pull the faceplate out. Then, you can remove the inside faceplate using a flat-head screwdriver. After removing the faceplate, you can remove the bolt and screw from the lock cylinder.

A locksmith can determine if you need to replace or rekey your lock. They can also give you suggestions on the most secure measures for your home. They can also make the necessary modifications to your door and frame to ensure a perfect fit. They also provide a warranty on their work.

You must purchase a new lock key before you can rekey it. It is important to use the lock key that is fitted snugly. A key that is not the right size can harm the internal mechanism of the lock and stop it from working. Insert the key into the lock to test its size. If it is flush with the plug, it's the right size. If the pins stick up from the top of plug, then they are too long.

There are many reasons why you might want to replace your door lock, for example:

If you're moving into a previous owner's residence or lose keys, rekeying your lock is an economical alternative than replacing it. It's also less costly than a complete upvc replacement window locks. However, there are some situations in which rekeying your repair upvc window lock isn't feasible. If the upvc window lock repair has been damaged or jammed repeatedly, for example, it may be time to replace it.