• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Window Panes

A cracked window pane is an inconvenience. This can be an opportunity to upgrade your windows to energy efficient or insulated ones and enjoy benefits such as improved comfort, increased resale values and lower utility costs.

This is a project you could tackle yourself at less than the cost of hiring a professional. It requires the right tools and only an hour or two of your time.

Glass

If your single-pane windows are old broken, deteriorating or damaged replacing them with more modern glass that is tempered or insulated will increase energy efficiency and reduce noise while preserving the original character of older homes. Most homeowners with basic hand tools can replace a window pane. In addition to a replacement pane, the following tools are required for the replacement process: latex glazing putty pliers, glazier's points and an electric heater to warm the old putty, if needed. Before beginning, wear gloves and safety glasses as working with broken glass could cause injuries.

Begin by removing any remaining broken pieces of glass. It is best to use pliers for this, but a flathead can be useful as well. Utilize a wood chisel or putty knives to remove any remaining old putty around the frame and window sash. Take your time and work slowly and be careful not to break the existing Window replacements near me sash. It is recommended to do this on a sturdy ladder rather than the ground and have someone stand below the sash to help keep it steady.

Once you have removed all the old putty, it is time to prepare the window frame to fit the new pane. Find the width and the height of the opening in the sash and subtract 1/8 inch from each measurement (to allow for seasonal expansion and contraction). These measurements can be taken to an hardware or home centers store to get an item cut from stock glass to the right size. You can also cut the glass by yourself if you have the appropriate tools.

After putting the new pane in place After installing the new pane, apply a small amount of caulking around the edge to ensure it is weatherproof. Install a glazier's pointing on both sides of the frame. This will ensure the pane. The points should not be so tight as to cause friction between the sash and frame, but they also shouldn't be too loose.

Before applying the putty on the surface, you must knead it thoroughly until it is soft and free from lumps. Cut it into pencil-sized pieces. Apply the first strip to the corner of the frame, moving from one corner to another so that it is even and smooth.

Glazier's Points

The glazier's points are small triangular pieces of metal that allow glass to be secured into the frame of a window without scratching or damaging the fragile surface. It's simple to learn how to use this secret tool, and you'll save money on the expense of a professional installation.

After the old putty as well as glazier's points are removed, thoroughly clean the frame with a knife to eliminate any remaining residue. If needed it is necessary to lightly sand the wood in the rabbet grooves to smooth rough areas. If you sand wood, protect it with painter's tape to avoid accidental damage.

Note down the dimensions of the frame. Bring these measurements to a hardware store or home center, and have the new pane made slightly smaller than the frame's opening. This will ensure that the pane fits snugly and allows for expansion and contraction.

Place the new window in the frame and press it into place firmly with your hand. Then, you can use the point of your chisel, or the back of the putty knife to make a tap on the glazier's facets, as illustrated in Figure 11. After you're done, the points should be flush with the top edge of the pane, and the shoulders of the points should be just below the rabbet's rim groove.

Apply a small amount of glazing compound over the edges of the new glass and into the rabbet grooves, to seal and protect them. Let it dry and cure fully.

Once the glazing compound has dried, you're ready to install the new window sash. The first step is to coat the wood with a heavy coat of Linseed oil. This will keep the new putty from sucking in the moisture and drying out and cracking with time. Use a brush to apply this coat, or the tip of the blade. Then, use the chisel that is on the back of the tool or the back of the putty handle to gently smash the new sash or glazier's tip into the grooves of the rabbet. Repeat this process in intervals of 10 inches around the frame.

Putty

A baseball hit or a rock thrown by error, or a fallen tree can cause a broken or cracked window pane. Fortunately, the majority of windows can be replaced by simply putting a brand new piece of glass in its the right place. The glass is held in position by a small metal clip, referred to as a glazier’s point and putty. This compound is also called glazing compound. Before installing a replacement pane, first get rid of the old one and clean up the area with a rag and a pull-type paint scraper or an abrasive wood chisel. Wear safety glasses and gloves while working. You'll need a heating gun in the event that the window is glued to the frame.

If you are planning to reinstall your original sash, remove the mold that holds the old pane. Then you can sand the sash down to ensure it's smooth and ready to be re-caulked. After the sash has been put back in place it is possible to apply a silicone caulk over the glass. This will ensure that it doesn't get soiled or discolor over time.

Remove the glazing points in the rabbets. These are the grooves on the sash where the glass is. If they're hard to chisel out, try holding a hand tool like a heat gun to soften them first. If you're using a heat gun, make sure not to cause damage to the sash or its railings by holding the tool too close.

Once the old points of glazing and putty have been removed, make a bed for the new pane. Roll a rope made of glazing compound between your fingers, and make it around 1/2 inch thick. Press it into the rabbets where the glass will be put. It is crucial that the glass sits on the putty on both sides If you have to do so, gently tap the glass into the rabbet with your thumb.

If the new pane has a crack you can fill it with a solvent-based glass glue or silicone caulk prior pressing it into the sash. If the crack is not sealed, you'll need to use putty to keep the water out. After the putty has dried remove the oily film from the glass and let it dry completely before painting. Paint after the putty has completely dried. It won't form a good seal and could be leaking or discoloring over time.

Paint

If you've suffered a break in a window pane, you may be worried about the expense of a new one. The truth is, replacing a single piece of glass windows replacement doesn't have to be costly even if you do it your own. Even a double-paned window can be replaced at a fraction of the cost it costs an expert.

First, if you are working on a large-sized window, ensure that it is securely fixed to the frame. With the right tools and techniques to make this task relatively easy and quick.

When you are ready to start with the removal of the window pane. Remove the glazing points made of metal that are attached to it. These are small metal triangles that function as "nails" to hold the window within the frame. They are buried beneath a bead or glazing putty which hardens into an unbreakable wedge which holds the wood frame securely in place and conceals the edges.

After removal of the old pane clean the frame and the wood. Scrape off any paint and sand down the rabbet grooves where the glazing points used to be. Sand them to bare wood surfaces, so that you can paint the frames the same shade. After sanding, apply a coat of flax oil to the wood that is not sanded down to extend the life of the frame.

The next step is to measure the dimensions of the window's opening. You will need to measure the vertical and horizontal dimensions of the entire opening, as well as the thickness. To determine the exact dimensions of the new pane, subtract 1/8 inch from both measurements. This will allow for seasonal changes in the glass. You can bring these measurements to a hardware store or home improvement shop and have the glass cut for you.

Now, it's time to bed the new window pane. To do this, place the pane inside the frame and move it around until a 1/16 inch of putty remains between the edge of the glass and the sash on all four sides. Use a putty knife to smear the putty evenly, making sure that there isn't an excessive amount of excess putty in the corners and along the edges. When the putty dries, it can be painted with the same color as the frame to prevent water and air from leaking into the frame and causing fogging.