• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix door hinge a Loose Door Hinge

Fixing a door hinge that is loose is a simple task for most homeowners. If, however, the screw holes are damaged and aren't able to hold screws, you might have to add dowels and wood glue before you can put back the hinge.

Before you do that though, brush away surface rust. This will help to keep the dowels in their place and provide an adequate base for them to rest on.

Removal of the Hinges

Many standard door hinges can be removed, which makes it easier to move the door from one side to the other or to take the entire door off the frame if need be. It is simple for anyone with patience, although you need to know how do it properly.

If the hinges have been painted you'll need to take off it before you attempt to remove the pins. If you don't, the paint will peel off and scratch your door when you try to lift it. Place the hinges in an stainless steel pot and fill it with water to the point that the hinges are submerged. Let the hinges rest in the pan for about 30 minutes. The heat of the water will soften the paint, making it easier to remove.

Once the pins are loosened and the pins are loose, you can take off the hinges from the frame and door. You can use a screwdriver to get the job done, but it is recommended that you make use of a magnetic screwdriver for this project. This type of screwdriver is specifically designed to take out metal screws and help you get the job accomplished much faster.

It is a good idea to spray lubricant on the hinges prior to trying to remove them. A simple lubricant can help you accelerate the process and make the removal of pins and screws more easily. This kind of lubricant can be found in a variety of hardware stores as well as home improvement shops.

You should also keep in mind that the number of door hinges you will need will vary depending on the kind of door and the configurations. Doors with a heavier core and solid-core will require more hinges, while hollow-core doors that weigh less might require just two or three hinges.

Understanding the different kinds of hinges will help determine which one is suitable for your situation. Exterior hinges are designed to withstand the weight of a door, while interior hinges must be able to support heavier loads.

Reattaching the Hinges

Sometimes a door hinge will get looser and eventually begin to hang out of alignment or slide. This can be a major issue, but the solution is usually quite simple. Most of the time it's a simple tightening of the screw will solve the problem. If the screw holes have been stripped out, it can be difficult to do. However, there is a trick to make these holes back to their original size using a wooden dowel.

Start by drilling the old hole using a drill bit close to the new screw size (normally 3/8"). Fill in the hole using wood glue and a wooden stick. The dowel should be cut to a length similar to the screw to ensure a tight fit. Then, you can reinstall the screw and tighten it to the desired level of tightness. If the door has an tendency to get stuck the door, then add a second dowel to the gap and repeat the process. Make sure to close the door slowly to examine the clearances around the perimeter after each adjustment.

You could also use a wood plug in place of the dowel. This will work as well, but may take some time to set up. You can tap in a piece of wood that has been whittled down to the right size. If you don't own a woodworking instrument You can use toothpicks or matchsticks made from wood.

Use a countersink to make the hole smaller for the head of screw after you have put it back in place. This will prevent the screw from hitting the edge of the bi-fold doors hinges as they are opened and closed. This will make it easier to tighten the screws before replacing hinges.

Once you have reinstalled the hinge, be sure to coat it with a dry lubricant to ensure that it doesn't get stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. Apply a thin coat and give it about 15 minutes to fully penetrate the barrel of the hinge.

Refinishing the Hinges

If you're not yet ready to replace replacement window hinges, you could try a few simple fixes. Check that the screws that hold the hinge plate in place to the door frame and the frame are tight. If they're loose, tighten them using a power drill or screwdriver. Be careful not too tighten the screws, as this can cause gaps to form at the trim joints, or worse, strip out the threads.

If the issue is that the hinge plates are splitting they can be reattached to the plates by putting wood glue to the side of them and inserting wooden dowels or toothpicks in the holes. Dowels or toothpicks will give a solid foundation for the screws and prevent the plates from shifting when you drive them into place. Allow the glue to dry before you can reattach your hinge.

The screws could also be smashed or gone. You can fix this problem by replacing the screws with longer ones. Make sure you use the correct drill bit for the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

Close the door once you've reattached your double glazing window hinge repairs and measure the gap between the frame and the door. The gap should be the thickness of a penny or less if an older door was not properly hung. If the hinges were put in place correctly, this should not be an issue.

If you notice that the hinges are loose, try adding an extra thicker shim between the hinge plate and the mounting surface, to create some extra space. You could also try removing the hinge pin from the problem hinge and pounding it with a hammer to make it tighter or use a new hinge pin altogether. You can also lubricate your hinges using mineral oil or jojoba to decrease friction and help keep them in position. Lubricating your hinges periodically can stop them from becoming stiff and squeaky, and also prolong their lifespan.

Cleaning the Hinges

The friction generated by the constant movement of a hinge attracts dust particles. Without periodic cleaning and lubrication, the particles become stuck in the moving parts of a door hinge and then build up over time. As a result the hinge becomes stiff and creaky and its appearance could be damaged quickly. Regular cleaning, lubrication and inspection can preserve the integrity of a hinged door and ensure their proper function.

Examine the hinges for signs of corrosion. If the rust is so severe that it has damaged the surface of the screw holes or the barrel of the hinge, you'll need to replace the hinges. If you're able to save the hinges, you can remove any loose rust using steel wool and wire brush. Then, apply a rust remover from a commercial store or homemade solution like lemon juice to the hinge. Let the rust removal solution remain on the hinge for several minutes to penetrate and dissolve any remaining rust.

Retightening screws can restore hinge functionality in the event that you don't want to spend money or time to replace hinges. If you've sanded the screws however, it might be necessary to attach a wooden dowel or shim to the hinge. Dowels made of wood are round pieces of wood in the form of rods which are available in various lengths and sizes. They are available at home improvement stores, woodworking supply and craft shops, or online.

You can also create a shim from a piece either plastic or metal, depending on the kind of hinge you own. To make a dowel, you need to cut an unfinished dowel into the desired length. You can then dip the dowel in a glue for carpenters and then insert it into the stripped hole, allowing the glue to hold the dowel in place.

Before cleaning the hinges, lay down a paper cloth or towel to shield your flooring from spills. After you have protected the area clean the hinges with an easy sponge or cloth dipped into mild cleaner to get rid of dirt and grime. Also, tarnish and rust can be removed. A small or toothbrush can be used to access hard-to-reach areas in crevices and narrow spots.