• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

How to Replace a Kia Sportage Replacement Key

The key of a lot of Kia models comes with an electronic keyless entry system built into. This key typically resembles a remote control and is able to be replaced with a brand new one from a kia ceed key fob programming dealer or locksmith.

Key fobs might stop working for several reasons, including batteries that are dead, worn buttons, water damage, signal interference and a malfunctioning receiver module. Here are some suggestions to help you get your kia sportage key fob programming sportage replacement key to work again.

How to replace the remote key or smart key?

No matter if your kia key programming comes with an intelligent key, remote key, push to start key or a regular non-transponder steel key, the battery in these keys will eventually need replacing. This is particularly relevant if your car displays a message indicating that the remote or smart key is not powered by the battery.

Luckily, it's a relatively simple process. To replace the battery of the keyfob, remove your mechanical key from the slit at the back of the fob. Then, pull the cover open. Inside the key fob will be an incredibly small screw that holds the battery in its place. Utilizing a small screwdriver unscrew the screw and pull out the old battery. Insert the new battery and close the cut on the key fob.

Test the key fob by pressing the lock or unlock buttons. If the doors lock and unlock according to your expectations, then you're all set! You can now take advantage of the hands-free lock/unlock feature on your Kia when your fingers start to get cold or you have to do some errands in Brandon.

Not all key fobs could need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith can access. Other keys (non-transponder metal keys) don't require programming. If your key needs to be programmed again, you must be aware of the key code stamped on the tag that identifies the key and record it in a safe location.

How do you replace the battery?

If the Kia key fob is unable to respond to pressing the lock or unlock button, it's a sign that the battery is depleted. A low battery may also cause other issues like the check engine light turning on or delayed engine cranking. Fortunately replacing the key fob battery is a relatively easy DIY task that requires only a few basic tools.

Be sure to turn off your vehicle and shut all doors prior to starting. Find the small metal or a plastic piece near the bottom of the key fob. Press it until the key pops out. Then, you can insert the key into the handle of the door for the driver to open your car.

To replace the battery on the key fob remove the cover that covers the rear. Use a pry tool to loosen the latch that holds the black negative cable. Remove the old battery, and then place the new battery to ensure its "+" side is facing you, and the "-", negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into place and avoid excessive force to avoid bending or damaging the contacts of the metal.

After you have installed the new battery, turn the key fob off and on in the ignition until the door locks up. You can then test the Kia's key fob to ensure it's working as intended.

How to replace a smart key

You could have a standard keyfob, or a Smart Key, based on the model of Kia Sportage. The smart key comes with an embedded mechanical key blade, while the standard keyfob does not. Both kinds of key fobs come with an internal battery which eventually needs to be replaced. Fortunately, this is an easy process that takes just two minutes.

Before you start before you begin, ensure that you're on a level surface with enough lighting and that the kia rio key replacement cost is off. Be aware that there are small parts inside the fob that can be removed if not cautious.

The first step is to locate the small release button that is located on the backside of the fob. This will be either a circular button or rectangular slot. Once you press this mechanical key blade, it will appear and you will be able to open the key fob.

After the key fob has been open, remove the battery. The new battery is one called CR-2032 and can be purchased through the internet or at a local auto parts shop. After installation it should be possible to lock, unlock and start your car using your key fob - even if your engine isn't running!

How do I replace the mechanical key?

The kia sorento key fob programming key fob is a great feature that lets us lock and unlock our car at the touch of an button. Like any device, the Kia key fob can occasionally have problems. There are ways to resolve these issues and keep your key fobs functioning for a long time.

One of the most frequent problems is a low or dead battery. The fob could be able to cease working or to work intermittently. If this is what you are experiencing it is time to replace the battery a new one.

If this isn't enough to solve the issue, you can use a flathead screwdriver standard to push the fob's casing made of plastic open. Be careful not to damage any internal components or scratch the plastic. Once the battery is removed and replaced, you can replace it with a brand new one.

Close and open the door with the mechanical key. (Every 2013 kia sorento key fob fob comes with an emergency mechanical key which will fit into the slot). Test the key fob to ensure it's functioning properly. Contact a dealer or a locksmith to solve the issue in the event that the fob is not working. Make sure they cut you an emergency key that can work in all the door and trunk cylinders to avoid lockouts in the future.