• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

How to Do a Door Lock Change

The change of your door lock is a simple and affordable way to improve the security of your home. This isn't for all. It requires a certain amount of skill and perseverance.

You must replace the cylinder, which is within the knob's body. The cylinder is responsible for recognizing the key as it is put into the lock.

Remove the old lock

First, you must remove the old lock. It is a fairly simple process, but it is important to keep certain things in your mind. Make sure the new lock fits the door. This will ensure that it is securely fitted and won't leave a gap at the latch or deadbolt.

After you have removed the latch plate look for two bolts or screws on the inside of the casing that hold the casing and the halves of the lock together. Unscrew them using a screwdriver, then take the lock out of the door. If you are using a mortise locking system, there is a set screw that holds the handle to the spindle. Use a screwdriver to unscrew the screw, and then take out the doorknobs.

Take the deadbolt and latch plug from the door jamb. Then, you can put in your new lock. If you are replacing a mortise you must determine the distance between the lock case and the door edge to ensure that the new lock will fit.

You might want to change your lock for a variety reasons, for instance, when you suspect that someone else is holding the key or if you've got an incoming roommate. You could save money if you remove the lock yourself instead of hiring for a professional. It's much easier than you think and can be done in a matter of a few minutes.

Remove the handle and trim of your door. With a flat screwdriver pry off the trim. You should be able to twist off the majority of it. In some instances you may be able remove the handles completely. Next, examine the handle for a tiny pinhole on the inside. Then insert a straightened clip into it. This will trigger the release mechanism, which allows you to take off the handle. Then, look on the inside of the lock for a small tab and press it using a screwdriver that is flat. After the spindle has been removed, you can remove the cylinder and the housing.

Making a decision on a new locking system

There are a lot of options available when it comes to selecting the right lock. Take a look at the various types of locks and choose one that matches the design of your door. Think about the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole along the edge of the door frame). Choose a lock that fits the door's thickness and swing.

The American National Standards Institute and BHMA have graded all door locks to give an idea of their longevity and the difficulty to pick them or disable them. A lock of grade 3 could be perfect for a quiet apartment in the countryside, whereas a lock of grade 1 could be better suited to a busy street near an open-air storefront.

Most smart door locks require a digital code to open. If you're worried about hacking or other security concerns seek out a professional locksmith or your local police department for assistance.

Replacing the cylinder

It is easy to replace damaged or broken door lock cylinder with an easy DIY project. The key is to choose the correct cylinder and follow the instructions that are included with it. First, you must remove the handle or knob if it is present. Then, using a screwdriver, remove the trim that is around the upvc window lock repairs cylinder. Once the trim has been removed, you can reach the screws that hold the cylinder in place and remove them using a flathead screwdriver. The cylinder is then gently pulled out of the door.

Before you install the new cylinder, be sure that it is the right length for the door you are using. Take a measurement of the distance from the center to the left and right sides of the cylinder using a tape measure. Buy a new cylinder that has the same measurements. This will stop cylinders from snapping when the door is kicked or the key becomes stuck inside.

Install the replacement cylinder into the door, and then turn the key. This will ensure that the cylinder is aligned with the carrier, which is usually located on the outside of the lock. After that, you can loosen the set screw which is supposed to be a couple of turns in the head. Also, you will need to loosen the screw at the door's edge that fastens the case, in the event that there is one.

You can you replace locks on upvc windows replace the lock cylinder you have used with the new one by sliding it into the case, and tightening the set screws. You should also reinstall the piece that connects the cylinder with the lock indicator stem and this can be done by pulling up three small tabs on back of the cylinder with needle-nose pliers. Then, you can attach the second bracket to the back of the cylinder. You must then install the strike plate and latch plate, as well as the retaining rings attached to the top of the double glazing window lock repair cost lock repair window locks upvc (visit the following page) cylinder.

Installing the new lock

If you're replacing an old lock, start by measuring the width of the door. Most locksets for residential use have a thickness of 3/8 inch to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll require a stronger door kit. This would include longer screws and either a longer spindle extension or the tail piece for door knobs.

The majority of locks come with a comprehensive installation guide to assist you. Before you begin, read the instructions to ensure that you have followed all the steps. The guide will give you a good idea of the amount of skill that is required to finish the task. It is possible to ask a friend who has experience changing locks for assistance if you are changing a lock the first time.

Before installing the new lock, it's a good idea to tape over the openings of the old hardware. This will prevent the screws from falling out of the holes and safeguard any tile you may have installed in the area. This will also protect your tiles from damage caused by dirt, rust and grime. SECURAM Touch comes with a strip painter's tape, which is designed to be used for this purpose, but you can also use gaffer's tape as well as masking tape if you have it available.

After you have removed the screws that hold the interior half of the lock section to the exterior side then pull it out straight away. It is important to do this swiftly to prevent the lock from closing itself in a way that could end up damage the mechanism.

Fit the new latch bolt in the upper cross bore of the new lock, if it comes with one. Be sure to put it in the correct position, which is usually indicated by an arrow on the faceplate. Then, screw the latch plate onto the bolt.

Finally, screw in the deadbolt and strike plate to the door jamb. Test the deadbolt by throwing it a several times to make sure that it extends all the way into the strike plate and is secured. If you're using an electronic smart lock, make sure to follow the included instructions to program it. This requires downloading an app and entering your email address, verifying your identity, and accessing the wireless network to connect your device.