• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

Door Lock Replacement - What You Need to Know

If the locks on your door start to show signs of wear and tear, it's usually recommended to replace them. This could be due to things like difficulty turning the lock or finding a key that doesn't fit.

The good news is that installing new hardware for your door is actually very easy. You only need to follow these steps.

Deadbolt

The deadbolt is the primary defense of your door against forced entry. It is stronger and more secure than the latch that operates the lock, so you'll need to ensure your new deadbolt is strong enough to meet your requirements. If possible, opt for a deadbolt made of case-hardened steel that doesn't have exposed screwheads on the exterior to prevent unauthorized drilling. To increase security, the interior side of your deadbolt should be drilled into the door frame.

When you install the deadbolt Make sure that the new deadbolt's bolt extends smoothly into the strike plate once you lock and close the door. If it isn't use a wood chisel to mortise the bolt hole in the strike plate and put the deadbolt back in place. When you lock and close your door, ensure that the latch of the doorknob meets the deadbolt's hole.

Check that the new deadbolt matches the old one before installing it. The majority of door locks come with an illustration of how to replace upvc door lock high the bolt should be placed above the doorknob. However, it's always recommended to consult a hardware expert if you are unsure what backset measurement you need for your doors. They will be able point you to models that work with your doors and the existing deadbolt opening.

Install the bolt assembly into the door hole, after making sure it is the correct length. If your new deadbolt is equipped with a latch faceplate, screw it in place and secure it, too. It's a good idea to attach the latch faceplate to the frame using the recommended screws as well.

Certain lock sets have a decorative or "dummy" bolt that lets you install the keyed-deadbolt and still have an effective latch. If you have this option, a dummy bolt should be installed with the same screws that are used for your faceplate of the latch and it is essential that the two fit together in a secure way to ensure maximum security.

Some deadbolts are accessible only through a thumb-turn, while others have two cylinders that allow both keyed and non-keyed access. It is best to select a lock that's commercial grade for maximum security. They are tested to withstand up to 250,000 cycles of closing and opening before they are sold to homeowners.

Latch

The latch is the part that retracts the bolt whenever you shut or open the door. It's usually secured by screws that are located on the side of the lock, but it may also be fastened to the strike plate or to the inside of the door jamb. It's important that you replace a door latch with the right one for the hardware you have. You can test this by putting the latch up to your existing hardware, or look at the label of the replacement. Dunn Lumber carries a variety of brands, but it is generally recommended to use the same brand as your existing hardware to ensure you receive an appropriate latch that fits correctly.

Some doors feature the appearance of a hasp, instead of a latch. A hasp consists of an elastic strap with a slot punched into it that fits over the staple. The staple is then fastened to the door frame or door by nail. When the door is closed and the strap is pulled, it is pulled down and secures it into the frame. Commercial buildings employ a hasp as it is cheaper than the lock.

Like any mechanism that has moving parts, a lock will wear out from repeated use over time. Sometimes, the internal mechanism may "stick" or become difficult to turn. This will require the replacement door locks of the entire lockset. Sometimes, the exterior doorknob can fail and it is essential to replace that as well.

If your lock is stuck, you can apply some graphite to the keyhole. You can either squirt some on the key or rub it on the inside of the lock, and then use the lock a few times to get the graphite into the mechanism. You can also employ a screwdriver for the removal of the knob that will expose the interior components and let you see what's going on inside the.

After you've removed the knobs, find the cylinder's two or three setscrews that run along the edges of the cylinder. Then tighten them by turning clockwise. You should also remove the faceplate and replace it. Surface-mounted rim locks come with an additional set of cylinder setscrews on the back of the case, which must be removed, as is the cover plate.

Strike Plate

The strike plate acts as a reinforcement and upgrade to a locking system. It is affixed above the holes for the deadbolts or master key systems bolts. It wards off intruders by ensuring that the latch of the lock is caught in the plate when the bolt is engaged. Apart from enhancing security, a high-quality strike plate can also improve the longevity of the lock.

Standard strike plates are flat metal plates with holes, or a series of holes, cut into them. It is fastened, usually with screws, onto the doorway's frame to give the latch an area to rest in when it is closed. The strike plate must be precisely aligned with the lockset to ensure the greatest protection against burglaries.

If the strike plate on a door is damaged, you should replace it as soon as possible. This will ensure that your door will close and latch properly. To replace a strikeplate first check that it is properly aligned with the bolt hole in the doorjamb. An easy way to accomplish this is to place tape over the bolt hole. Then, test the latch by closing and opening the door. If the latch doesn't work, remove the tape. Then chisel the area to create a level with the doorjamb.

After the area has been chiseled, it is crucial to use a larger bolt to secure the strike plate. They must be at least 3 inches long to ensure that they are securely fixed to a stud which is behind the trim board. If you do not use the screws that are longer, the wood in the doorjamb may split during a kick-in attack by a burglar and make the door vulnerable.

A professional locksmith is able to quickly replace the strike plate that has been damaged or worn out. They can also put the new strike plate onto a door that has never had one before. They can also upgrade existing strikeplates to increase the security of a building and its aesthetics. This can help a property owner attract tenants who are looking for a safe living environment and greater peace of mind.

Keys

The key cylinder of your lock is the part that receives the key to move pins so that the internal handle can turn. The cylinder is the most important component of your door lock, since it serves the purpose that locks were made for - to protect you, your family, and your belongings. Rekeying locks is a cost-effective alternative to replacing them.

The replacement locking mechanism for upvc doors of the lock is more complicated than simply swapping out the current handle-lock combo or deadbolt. The old hardware, cylinder, and handle (if you have the knob and lock combo) must be removed from the door before a new lock can be installed. There are numerous DIY-friendly tools that can be used to replace the door lock. However, it is recommended to speak with an expert locksmith to ensure that the job is done correctly.

It is essential to have the correct key before you can install your new lock and the cylinder. A key that is duplicate won't work and could cause the lock to fail completely, making it impossible to open. A professional can help prevent this from happening by making sure you have a an authentic, functioning key for your home.

The next step is to take off the faceplate, and then the latch plate. To remove the screws that hold them in place, you'll require the help of a screwdriver. You may want to leave them in place if the plates you are replacing a upvc door lock Upvc door Lock mechanism (chessdatabase.science) are identical to the original ones. This will save you time. If you must replace lock in upvc door them, be careful not to tighten too much the screws since this can weaken their grip on the door.

After you have removed the plates, you will need to measure for the new lock. It is essential to know the door's dimensions before visiting the hardware store. Although a lot of locksets available can be used today to fit a standard door thickness, it is best to get them in advance. Doorknob locksets are often different sizes from deadbolt locks, commercial models might come with a larger bolt or latch.