• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

• 페이스북 공유
• 트위터 공유

Reasons to Change Door Lock

You can change the lock on your door for a variety of reasons, from improving the security of your home to re-decorating your entryway. You may need to change locks when your key becomes stuck or is difficult to turn.

DIY novices can also alter their lock. Gather the materials needed to begin.

Remove the old lock

Removal of the old lock from the door is an essential step before installing the new lock. This is important when you suspect that someone else has a key to the home. It's also a good idea after you've moved into a new home, experienced a burglary or a roommate moved in. It's much easier than you think to complete and can be done in a matter of minutes.

Begin by taking off the screws that secure the deadbolt faceplate on the door frame. To remove the faceplate, you will need to remove screws on both sides. This will allow you to discover what's behind it and will give you a better idea of how to proceed with the remaining steps.

Once you have removed the old faceplate, you'll have to take off the bolt and strike plate. Remove the bolt from the door hole by using the screwdriver. If the bolt is rusty, you might need to use a chisel hammer it out. When using a chisel remove the bolt, make sure to not to damage the door frame.

Make sure the new deadbolt, doorknob and lock will fit in the holes that are already present in the door before removing the old one. Most hardware stores and big box stores sell different kinds of double glazing window locks replace and can assist you in choosing the best one for your requirements. If the lock you bought does not match your door, bring it back and seek help.

When you're removing the old lock, look for small notches or depressions in the handle or around the trim. If you can locate them, slide a straightened safety pin or flat screwdriver into these to loosen the handle and expose screws underneath.

Once the screw inside the handle is removed, you can begin to remove the knob from its spindle. To do this, find the set screw located at the base of the knob and loosen it. Then, take the spindle off.

Install the new lock

It is a good idea to change the locks on your doors regularly particularly if you've been the victim of a break-in. It's simple, inexpensive and efficient to change the lock on your door. Most people can do this themselves with a screwdriver and a few basic instructions. You may also want to learn how you can change the key on your door lock to ensure that only you have the key.

You'll need to purchase a new lock with the same keyway as the existing lock. Most locksmiths will rekey your lock for you at a cost however, you can save money by doing this yourself. You can purchase a new lock from hardware stores or online. Standard deadbolts will fit most doors. However, you will need to measure your door to make sure it is suitable.

Your new lock will often come with a diagram that will show you how to install it on the door. This template can be used to drill the hole. It is much easier than measuring every time. If the template doesn't match to the hole you intend to drill you need to return it to the hardware store and get an alternative.

When you install the new lock, you must remember to put it on the right side of the door. Check the latch. It should have a label that reads "up" or similar. Make sure that the latch is seated correctly in the plate and secure it using the provided screws.

If you're replacing a door knob lock, it's also important to pay attention to the way it's operated. Most knob locks are left-handed however there are a few that are right-handed. If you're not careful, the knob could be placed on the wrong side of your door, which will make it impossible to lock either from the inside or outside.

You should try the new lock after you finish. It should be able to lock and unlock the door using a key from the inside as well as the outside. If you aren't satisfied with the result you can always contact an expert locksmith to fix the issue.

Test the lock

A lock that does not unlock can be annoying but it can also put your family's safety at risk. It's easy to fix the majority of problems with door locks by tackling the issue and lubrication. To start with, check that your key is properly cut and that the lock isn't soiled or loose. If this doesn't fix the issue, try to lubricate the door lock actuator with powdered graphite or a silicone-based grease.

Check that the doorlock switch, wiring harnesses and actuator connectors are all working properly. To check this, consult the manual or wiring diagram to determine the purpose and color-coding of all door lock switch wires. Use a digital meter, or test light to verify that the actuator is receiving power and ground whenever the switches are turned on. If you notice an electrical voltage switch with each switch activation, that indicates the switches are good and it's likely the actuator that requires to be replaced.

If the switch seems to be working but the actuator doesn't move when you turn it, there could be a problem with the cylinder. The actuator cylinder has spring-loaded pins that prevent the cylinder from turning until the key is placed in and moves the pins upwards to fit the height of the key in that location. This causes the cylinder eventually to rotate opening the lock body and opening the handle latch to be opened.

If the door lock actuator still not working, you can take it off it by using a small screwdriver. You'll need to release the bolt that locks first, and then take off the plastic cover that houses the electrical connector. Then, disconnect the door double glazing window lock replacement actuator, and let it fall. Then you should be able to find and remove the two 10mm bolts which hold the actuator in place. After the actuator has been removed, you'll be capable of disconnecting the black electrical connector and then pull it out along with the actuator and lock assembly.

Replace the key

If you have a keyed deadbolt or door knob, when it isn't working properly you need to either change the lock's key or rekey it or replace it completely. It's not hard to do this yourself and could save you a lot of money. It is recommended to have a professional locksmith check the locks for any issues prior to starting. This will give you peace of assurance that your home is secure and safe.

To begin, remove the faceplate on the outside from the doorknob or deadbolt. There may be screws holding it in place, if so use a screwdriver to loosen them, and then pull the faceplate off. Then, you can remove the inside faceplate using a screwdriver that has a flat head. Once you have removed the faceplate, you are able to remove the bolt and a screw from inside the lock cylinder.

A locksmith can help determine if the lock you have needs to be replaced or changed. They can also give you advice on the best security measures for your home. They can also make any needed modifications to the door and frame to ensure a perfect fit. They also offer a guarantee on their work.

If you choose to rekey the lock, you'll have to first buy an additional key for it. It is important to use a lock key that is fitted snugly. A key that is not properly fitted could damage the mechanism inside and stop it from working. To determine the size of a key, insert it into the lock. If the key sits completely against the plug then it's the right size. If the pins extend from the top of plug, then they are too long.

There are many reasons you might want to change your door lock, including:

If you're moving into a previous owner's residence or have lost keys, rekeying your lock can be a more economical alternative than replacing it. It's also more cost-effective than a complete replacement upvc window lock repair near me Locks (postheaven.net). Rekeying an existing lock might not be feasible in certain circumstances. For instance, if the lock is damaged or has been repeatedly blocked, it's time to replace it.